MLC10 multilayer chip inductors electrical q vs. frequency characteristics: measured on impedance analyzer hpa4195a. indu c t a n ce vs . t emp eratu r e characteristics: measured on lcr meter hp4285a. impedance vs. frequency characteristics: measured on impedance analyzer hpa4195a. inductance vs. dc current characteristics: measured on lcr meter hpa4285a. t olerance: for 20% use m, 10% use k, and 5% use j as part number suf fix. mechanical solderability: 90% terminal coverage. preheat: 120 20 c for 60 se c. s olde r: h63a. solder t emp.: 230 5 c. flux: rosin. dip time: 4 1 sec. environmental therma l s hock: i nduct ance shall be wit hin 5% of initial value. q shall be within 30% of init ial v alue wit hin temp. r ange of -40 c to + 85 c for 30 min. each for > 100 cycles. hum idity resista nc e: sa me res ults as above. t emp. 4 c. humidity: 95% rh. time: 1000 hrs. high temp resistance: same results as above. t emp: 85 c. t ime: 1000 hrs. low t emp resistance: same results as above . t emp : -45 c. t ime : 1000 hrs. operating t emp.: -25 c to +85 c. storage t emp.: -40 c to +85 c. physical packaging: .022 h - 2.2 h, 4000 pieces per reel. 2.7 h - 27 h 3000 pi eces per 7 inch ree l. *see dimensional difference. MLC10-r022m-rc .022 20 20 50 320 0.20 300 MLC10-r068m-rc .068 20 20 50 280 0.20 300 MLC10-r082m-rc .082 20 20 50 255 0.20 300 MLC10-r10m-rc .10 20 25 25 235 0.30 250 MLC10-r12m-rc .12 20 25 25 220 0.30 250 MLC10-r15m-rc .15 20 25 25 200 0.40 250 MLC10-r18m-rc .18 20 25 25 185 0.40 250 MLC10-r22m-rc .22 20 25 25 170 0.50 250 MLC10-r27m-rc .27 20 25 25 150 0.50 250 MLC10-r33m-rc .33 20 25 25 145 0.55 250 MLC10-r39m-rc .39 20 25 25 135 0.65 250 MLC10-r47m-rc .47 20 25 25 125 0.65 250 MLC10-r56m-rc .56 20 25 25 115 0.75 150 MLC10-r68m-rc .68 20 25 25 105 0.80 150 MLC10-r82m-rc .82 20 25 25 100 1.00 150 MLC10-1r0k-rc 1.0 10 45 10 75 0.40 50 MLC10-1r2k-rc MLC10-1r5k-rc MLC10-1r8k-rc MLC10-2r2k-rc MLC10-2r7k-rc * MLC10-3r3k-rc * MLC10-3r9k-rc * MLC10-4r7k-rc * MLC10-5r6k-rc * MLC10-6r8k-rc * MLC10-8r2k-rc * MLC10-100k-rc * MLC10-120k-rc * MLC10-150k-rc * MLC10-180k-rc * 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 45 45 45 45 45 45 45 45 45 45 45 45 45 30 30 10 10 10 10 10 10 10 10 4 4 4 2 2 1 1 65 60 55 50 45 41 38 35 32 29 26 24 22 19 18 0.50 0.50 0.60 0.65 0.75 0.80 0.90 1.00 0.90 1.00 1.10 1.10 1.20 0.80 0.90 50 50 50 30 30 30 30 30 15 15 15 15 15 5 5 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 idc max. (ma) allied part number inductance ( h) tolerance (%) q min. test freq. (mhz) srf min. (mhz) dcr max. ( ) rohs 714-665-1 140 allied components interna tional www.a lli edcom pon en ts .com 0.0790.008 (2.010.20) 0.0490.008 (1.250.20) 0.0350.008 (0.890.20) 0.0200.012 (0.510.30) 0.039 (0.99) 0.045 (1.14) 0.047 (1.19) dimensions: inches (mm) MLC10-220k-rc * MLC10-270k-rc * 22 27 30 30 1 1 16 13 1.10 1.25 5 5 10 10 MLC10-r056m-rc .056 20 20 50 320 0.20 300 MLC10-r047m-rc .047 20 20 50 320 0.20 300 MLC10-r033m-rc .033 20 20 50 320 0.20 300 * 0.0490.008 (1.250.20) all specif icat ions subject t o change wit hout not ice. available in tighter tolerances. revised 2/06/09
|
